Ինչպիսի նյութ կարող է կտրել լազերային կտրող մեքենան:

21-րդ դարի սկզբից ի fiber laser cutting machine cut pipe have been continuously developed, laser cutting technology will be applied in various fields, and more and more suitable materials will be used. According to the different characteristics of different materials, the matters needing attention when using the fiber laser cutting machine are also different.

Կառուցվածքային պողպատ

Լավ արդյունք կստացվի, երբ նյութը կտրված է թթվածնով: Թթվածինը որպես վերամշակող գազ օգտագործելիս կտրող ծայրը մի փոքր օքսիդացվի: Մինչև 4 մմ հաստությամբ սալերի համար ազոտը կարող է օգտագործվել որպես բարձր ճնշման կտրման վերամշակող գազ: Այս դեպքում կտրող ծայրը չի օքսիդացվի: 10 մմ-ից ավելի հաստությամբ ափսեների համար օգտագործեք հատուկ թիթեղներ լազերային համար և վերամշակման ընթացքում յուղ կիրառեք մասի մակերեսին `ավելի լավ արդյունքներ ստանալու համար:

չժանգոտվող պողպատ

Չժանգոտվող պողպատից կտրելը պահանջում է. Թթվածնի օգտագործում, այն դեպքում, երբ ծայրահեղ օքսիդացումը նշանակություն չունի. օգտագործեք ազոտ `ոչ օքսիդացված և փչացած եզրը ստանալու համար, այլևս անհրաժեշտ չէ բուժում: Տախտակի մակերևույթի վրա յուղային ֆիլմի ծածկույթը կստանա ավելի լավ պերֆորացիայի ազդեցություն `առանց կրճատելու մշակման որակը:

ալյումին

Despite its high reflectivity and thermal conductivity, aluminum materials up to 6mm in thickness can be cut, depending on the alloy type and laser capabilities. When cutting with oxygen, the cutting surface is rough and hard. When using nitrogen, the cut surface is smooth. Pure aluminum is very difficult to cut because of its high purity. Only when a "reflection absorption" device is installed on the system can aluminum be cut. Otherwise the reflection will destroy the optical components.

տիտան

Titanium թերթը կտրվում է արգոնով և ազոտով, որպես վերամշակող գազեր: Այլ պարամետրերը կարող են վերաբերվել նիկել-քրոմի պողպատին:

Պղինձ և փողային

Both materials have high reflectivity and very good thermal conductivity. Brass with a thickness of less than 1mm can be cut with nitrogen; copper with a thickness of less than 2mm can be cut, and the processing gas must be oxygen. Copper and brass can only be cut when a "reflective absorption" device is installed on the system. Otherwise the reflection will destroy the optical components.

Սինթետիկ նյութ

Սինթետիկ նյութեր կտրելիս հիշեք, որ կտրելու վտանգները և արտանետվող վտանգավոր նյութերը: Սինթետիկ նյութերը, որոնք կարող են մշակվել, ջերմապլաստմասսա, ջերմազերծող նյութեր և էլաստոմերներ են:


Հրապարակման ժամը `հուն-28-2020
robot
robot
robot
robot
robot
robot