RFL-1000 usoro laser

2. Power ọkọnọ chọrọ : Atọ-adọ AC380V Frequency: 50Hz

(1) nke Atọ-adọ voltaji kwụsie ike ≤ ± 5%, atọ-adọ ike ahaghị nhata ≤2.5%

(2) The ike ọkọnọ na-eji ihe atọ na-adọ ise waya usoro na grounding eguzogide bụ ≤ 4Ω;

(3) N'ihi mgba ọkụ nkọwa, waya cross ngalaba, na njikọ ụzọ mee ihe n'ihi igwe ngwaọrụ, lasers, chillers, na ikuku compressors, wdg, na-ezo aka igwe ike nhazi esereese.

Note: ① The ike ọkọnọ voltaji na-adịghị ekwe ka nwere mberede jumps na Ugboro mberede ike ọdịda; ② Ọ bụrụ na ndị grounding eguzogide ike-emerịrị ≤ 4Ω, na grounding ga-ugboro ugboro. The usoro bụ ịzụta 3 (1M / ala) n'ala nkpa-n'aka nke ọkọlọtọ ọla kọpa-plated ígwè isi (ọla kọpa-plated ọkpụrụkpụ nke 0.25mm) na a size nke banyere Ф18mm lie ha n'ime ala na a omimi nke banyere 2.5M.

3. abịakọrọ ikuku chọrọ :

(1) Air ọkọnọ ikike: 1mL / min

(2) Air ọkọnọ mgbali: 0,8 ~ 1.0Mpa

(3) igirigi mgbe okpomọkụ bụghị elu karịa 5 ℃

(4) Oil content≤0.01ppm siri ike particles≤0.02μm

4. The n'ala chọrọ nke echichi saịtị : The ala dị larịị ma dị ọcha, na ntọala na-mere dị ka ihe ndị a chọrọ na ntọala map; dị ka e gosiri na nkwekọrịta

5. Environmental chọrọ maka igwe echichi saịtị :

(1) okpomọkụ chọrọ: The igwe ngwá ọrụ pụrụ enịm ke gburugburu ebe nke -10 ° C na 40 ° C; na laser ga-enịm ke gburugburu ebe nke 18 ° C na 25 ° C; ma ọ bụrụ na ọ na-apụghị-ruru, a iche iche ụlọ na ntụ conditioner ga-arụnyere;

(2) iru mmiri chọrọ: ≤70% (laser naanị)

(3) Ájá chọrọ: ≤1mg / m³, dịkwuo iyuzucha ájá ofufe.

6.The echichi gburugburu ebe obibi chọrọ nke chiller, ikuku Compressor na akpụkọta draya :

(1) The oyi-ihicha igwe na ikuku Compressor pụrụ enịm n'èzí. The gburugburu ebe obibi ga-akọrọ, na ájá-free, mmiri ozuzo na-àmà, wdg na otu mmiri anwụrụ n'etiti mmiri-obi jụrụ igwe na laser nwere ike gafere 10m;

(2) Ọ bụrụ na ndị chiller, ikuku Compressor na akpụkọta draya na-enịm n'ime, ha ga-ájá-free na ọma ventilated, na-ekpo ọkụ ikuku N'ịbụ chiller ga-pụchara n'èzí;

7. Cutting gas chọrọ : The-adị ọcha nke Cutting gas dabeere na-esonụ gas-adị ọcha. Ahịa nwere ike ịhọrọ na-adị ọcha nke gas dị ka n'ezie ọnọdụ nke na ọnwụ mmetụta:

Nitrogen: 99.7% (nkịtị nitrogen ma ọ bụ mmiri mmiri nitrogen) Nkịtị oxygen: 99,5% Pure oxygen: 99,95%

8. Jụrụ mmiri chọrọ

(1) Deionized ma ọ bụ distilled mmiri ga-eji. Ọ bụrụ na ọ na-apụghị-anọchi na barreled ọcha mmiri, ịnweta mmiri ike-eji, ma ọ bụghị ndụ nke laser ga-emetụta;

(2) ebe n'okpuru oyi na oyi, na chiller ga-enịm ke gburugburu ebe n'elu 0 ℃.

9.Laser echichi chọrọ

(1) Mgbe laser arụnyere na kowe, na laser tilt n'akuku bụ ihe na-erughị 5 Celsius;

(2) elu ohere chọrọ nke laser: dịkarịa ala 1.5 mita ohere gburugburu laser, na n'elu uwa nwere ike ikwe ka 1 mita nke uwa si n'elu ụlọ;

（3） Working environment temperature and humidity: The working environment temperature is 25 ℃ ± 2 ℃, the temperature fluctuation is small; the ambient humidity is less than 75%, and it will not condense and dew. Recommendation: If the customer's environment is poor, the laser must be in a separate room with air conditioning;

(4) Ft ntọala chọrọ: n'ala ibu: n'ala ibu dị ukwuu karịa 1500kg, n'ala ga-ewepụghị na boo, unevenness bụ ihe na-erughị 6mm

(5) E kwesịrị dịghị ngwá na oké vibration gburugburu laser, ya bụ, laser ike arụnyere bụ n'ala na-vibration;

（6） Power requirements: Power supply requirements for customers' power grid 380 ± 10%, 50Hz, three-phase, neutral-to-ground; regulator output 380 ± 2%, 50Hz, three-phase, neutral-to-ground, 50KVA

na-aṅụ