လေဆာဖြတ်စက်ကိုဘယ်လိုပစ္စည်းမျိုးဖြတ်နိုင်သလဲ။

၂၁ ရာစုအစတွင် fiber laser cutting machine cut pipe have been continuously developed, laser cutting technology will be applied in various fields, and more and more suitable materials will be used. According to the different characteristics of different materials, the matters needing attention when using the fiber laser cutting machine are also different.

သံမဏိကိုယ်ထည်

ပစ္စည်းကိုအောက်စီဂျင်ဖြင့်ဖြတ်သောအခါရလဒ်ကောင်းများရရှိလိမ့်မည်။ အောက်စီဂျင်ကိုဓာတ်ငွေ့အဖြစ်အသုံးပြုသောအခါဖြတ်တောက်ခြင်းအစွန်းသည်အနည်းငယ်ဓာတ်တိုးနိုင်သည်။ အထူ ၄ မီလီမီတာအထိရှိသောအပြားများအတွက်မြင့်မားသောဖိအားဖြတ်တောက်ခြင်းအတွက်နိုက်ထရိုဂျင်ကိုပြုပြင်ထုတ်လုပ်သောဓာတ်ငွေ့အဖြစ်အသုံးပြုနိုင်သည်။ ဤကိစ္စတွင်, ဖြတ်တောက်ခြင်းအစွန်းဓာတ်တိုးလိမ့်မည်မဟုတ်ပါ။ ၁၀ မီလီမီတာထက်ပိုသောအထူရှိသောပြားများအတွက်လေဆာအတွက်အထူးပြားများကို အသုံးပြု၍ ပိုမိုကောင်းမွန်သောရလဒ်များရရှိစေရန်ပြုပြင်ထုတ်လုပ်နေစဉ်ဆီ၏မျက်နှာပြင်ပေါ်တွင်ဆီကိုလိမ်းပါ။

အစွန်းခံသံမဏိ

သံမဏိကိုဖြတ်တောက်ရန်လိုအပ်သည်မှာအစွန်းဓာတ်တိုးခြင်းကိစ္စသည်အောက်ဆီဂျင်အသုံးပြုရန်ဖြစ်သည်။ non-oxidized နှင့် burr-free အစွန်းရရှိရန်နိုက်ထရိုဂျင်ကိုအသုံးပြုပါ၊ နောက်ထပ်ကုသမှုမလိုအပ်ပါ။ ဘုတ်၏မျက်နှာပြင်ပေါ်ရှိဆီအဖုံးကိုအဖုံးအုပ်ခြင်းသည်ပြုပြင်ခြင်းအရည်အသွေးကိုလျှော့ချခြင်းမရှိဘဲပိုမိုကောင်းမွန်သောဖောက်ခြင်းအကျိုးသက်ရောက်မှုကိုရရှိလိမ့်မည်။

လူမီနီယံ

Despite its high reflectivity and thermal conductivity, aluminum materials up to 6mm in thickness can be cut, depending on the alloy type and laser capabilities. When cutting with oxygen, the cutting surface is rough and hard. When using nitrogen, the cut surface is smooth. Pure aluminum is very difficult to cut because of its high purity. Only when a "reflection absorption" device is installed on the system can aluminum be cut. Otherwise the reflection will destroy the optical components.

တိုက်တေနီယမ်

တိုက်တေနီယမ်ကိုအာဂွန်နှင့်နိုက်ထရိုဂျင်ဓာတ်ငွေ့ဖြင့်ထုတ်လုပ်သည်။ အခြားသတ်မှတ်ချက်များသည်နီကယ် - ခရိုမီယမ်သံမဏိကိုရည်ညွှန်းနိုင်သည်။

ကြေးနီနှင့်ကြေးဝါ

Both materials have high reflectivity and very good thermal conductivity. Brass with a thickness of less than 1mm can be cut with nitrogen; copper with a thickness of less than 2mm can be cut, and the processing gas must be oxygen. Copper and brass can only be cut when a "reflective absorption" device is installed on the system. Otherwise the reflection will destroy the optical components.

ဒြပ်ပစ္စည်း

ဒြပ်ပစ္စည်းများဖြတ်တောက်သည့်အခါဖြတ်တောက်ခြင်း၏အန္တရာယ်နှင့်ထုတ်လွှတ်နိုင်သောအန္တရာယ်ရှိသောအရာများကိုစိတ်စွဲမှတ်ထားပါ။ ပြုပြင်နိုင်သည့်ဒြပ်ပစ္စည်းများမှာ thermoplastics, thermosetting ပစ္စည်းများနှင့် elastomers များဖြစ်သည်။


post အချိန်: ဇွန် -28-2020
robot
robot
robot
robot
robot
robot